Harness/ Guide/ Something

[Walt]

I would sure be interested in hearing what others have tried as a method{s} for holding the V2K. I am currently using a harness around my neck to hold the unit in place. I have tried putting the hose thru a belt around my waist….etc etc. This issue seems to be the number one issue for most guys.

[Walt]

Damn that is a good idea I would have never thought of… you nasty man. I’m going to search online for this. I am hoping it is flexible enough to slide up and down on my shaft

[Walt]

Again thanks for the suggestion. I ordered one last night off Amazon cost was 9.99. A cheap price to pay it will be here on the 30th and looking forward to giving it a try. From your description and photo’s I think it give me the hands free experience I am looking for. I also enjoy edging and hate having to re-adjust the unit. Also like your idea for using it on your bed. I mainly like to set back while watching some porn and letting my VK2 just do it’s thing- slowing down or stopping when I get close. Imagine most guys do the same thing. You have any other suggestions be sure to post 🙂

[Jeff]

Here’s a solution which works, especially if you like to mix your V2000 with rubber; I have latex pants that have a penis ring built in. With the pants off stretch the ring over the bottom end of the receiver and then lubricate the inside of the receiver and put the pants on. Connect everything up and away you go. The pants will hold the receiver in place. For a very snug fit use close fitting pants, for a bit more movement use oversize pants. Another variation on this theme is to use pants with a penis sheath built in. Cut the tip off of the sheath and stretch the sheath over the end of the receiver. This allows a good amount of movement of the receiver but still holds it in place.

[Jeff]

Oh by the way, I’m in the UK so by pants I mean briefs!

[adamv2kfan]

Jeff, thanks for the suggestion.

I’d been thinking about something similar for awhile.

I use j-lube, and while cheap I find that it dries out quite fast, especially along the shaft of my cock, causing the receiver to grip rather than glide. Having to pull out and re-lube kinda breaks the mood a bit — plus it’s kinda messy.

I’ve modified my Venus end-cap to have constant suction from a vacuum pump instead of the ball-valve.
This also doesn’t help with lube retention. I figured the vacuum probably slowly sucks the lube towards the top of the receiver.

I’d wondered if there was some way to create a “lube reservoir” at the base of the receiver so that the bottom of my shaft is constantly re-lubricated. I think I might have found the solution — latex briefs with a penis sheath.

My plan is to cut the tip off the latex sheath and stretch the open end over the end of the venus receiver, similar to your suggestion. It would aid pop-off (not really a problem given the added suction from my mod) but the briefs would also create an sealed space around the base of my cock and the receiver to fill with lube. I’d imagine filling the briefs with copious amounts of lube, combined with the slipperiness of the lubricated latex will feel great too — cock, balls and asshole all covered in lube and encased in tight latex. I’ve even ordered a small, longish butt plug with a flush base to combine with this setup.

The kit arrives early next week. I’ll let you know how it goes!

[Scott Cruickshank]

Not saying this is the best, just how I rigged mine.

I found a small tube and built it up in two places top and bottom using electrical tape. You build it up a little to hold the guide tube away from the receiver a bit. Just keep wrapping the tape around until you have a little roll built up. Then you tape the tube to the side of the receiver with three or four wraps stretched tight. Then find a very stiff thick gauge wire and bend a loop at the bottom something like what you see in the photo below. You sit or lay on the loop with the straight part pointing up between your legs. Thread the guide tube onto the wire and have at it. The receiver will glide up and down along the wire making for a fairly steady hands free motion. Mine does rock side to side a bit but nothing that causes any control problems. A bigger loop would probably solve that. I also silver soldered the wire joints where they wrap around and join to make sure it would cause no skin pinching. You could probably just as easily ball them up with tape. I used a small piece of very light steel pipe, but I’m sure plastic would be fine, something like the barrel from a cheap ball point pen with the guts pulled out. It seems to add no appreciable noise.

I’ll say this, once you got a hands free solution, whatever it is, you never go back to the old way.

[Author]

Posts